Paints and Varnishes in aqueous phase

Products EMADOX® : A4, ICP  and  AB RUST®: NFP, FP, AE v2

 

EMADOX® A4

Without V.O.C.
Corrosion inhibitor – Anti flash-rust additive

EMADOX® A4 is a corrosion inhibitor which contains sodium nitrite.

Advantages:
Very efficient on safes iron or steel supports: usual dosages of 0.2 to 1.0% of the total weight for anticorrosion primaries based on pure acrylic resins or modified, alkyd emulsion, two component epoxy.Convenient for the protection of aluminum.
To avoid the development and the rise of the rust through the paint film on bad stretched iron or steel supports: in this case, the incorporation rate must be over than: contact our technical support
Uses:
Anti flash-rust additive
Protection for metal packaging (boxes, buckets of paints and varnishes)

 EMADOX® ICP

Without V.O.C. – without Nitrite
Compatible with the EUROPEAN ECOLABEL
Corrosion inhibitor – Anti flash-rust additive

EMADOX® ICP is a corrosion inhibitor without sodium nitrite.

Advantages:
Higher anti flash-rust efficiency : utilization rate of 0.4 to 1.0% from the total weight. Specific odor less strong than other inhibitors without nitrite of our ranges.
Uses:
– Anti flash-rust additive
– Protection for metal packaging (boxes, buckets of paints and varnishes)

 AB RUST® NFP

Without V.O.C. – without Nitrite
Compatible with the EUROPEAN ECOLABEL
Corrosion inhibitor- Anti flash-rust additive

AB RUST® NFP is a corrosion inhibitor without Nitrite for paints and varnishes.

Advantages:
Efficiency :Rates between 0.4 and 1.0% of the AB RUST® NFP additive from the total weight of the formulation permitted us to eliminate or to limit really significantly the phenomenon on steel supports freshly painted and exposed in atmosphere saturated in moisture for a period at least equal to the drying period to touch.

Versatility compared to resins:

L’AB RUST® NFP has shown in our laboratory tests a good chemical compatibility with binders based on resins:

  • Acrylic
  • Styrene-acrylic
  • Alkyd in emulsion
Versatility compared to metals:AB RUST® NFP protects ferrous metals, aluminum, zinc.
Uses:
Anti flash-rust additives
Protection for metal packaging (boxes, buckets of paints and varnishes)
Special recommendation:
Stability at low temperature: reversible crystallization on samples stored at -5°C and -10°C
It is recommended to store the AB RUST® NFP frost.

 AB RUST® FP

Without V.O.C. – without Nitrite
Compatible with the EUROPEAN ECOLABEL

Corrosion inhibitor – Anti flash-rust additive

AB RUST® FP is a corrosion inhibitor without Nitrite, with an interesting rate cost/efficacy for applications with few constraints in terms of corrosion.

Advantages:
Compatibility with a large range of resins: dispersions and emulsions of acrylic polymers, polyurethane and epoxy two component, resins acids.
Uses:
Anti flash-rust additive.
Protection for metal packaging (boxes, buckets of paints and varnishes).

 AB RUST® AE v2

Without V.O.C. – without Nitrite
Compatible with the EUROPEAN ECOLABEL

Corrosion inhibitor – Anti flash-rust additive for alkyd emulsion resins

AB RUST® AE v2, with the origins of its components, shows a remarkable consistency when it is used as an anti flash-rust addititve especially in formulations based on alkyd emulsion.Although a systematic verification of the compatibility is essential, AB RUST® AE v2 pensures the protection of metal while avoiding the problems of destabilization of emulsions, freezing, etc.

Uses:
Additive Anti flash-rust.
Protection of metal packaging.